6 FET IRFB3077 INFINEON CONTROLLER (MOTOR WITH HALL SENSORS)
6 fet 3077, 36-50V Infineon Controller
Includes following functions as standard (we strongly recommend our matching Throttle are also purchased to make use of all functions and for plug and play simplicity:
• Throttle connection with Integrated push button cruise, separate 3 speed connection (Full and Half Twist include integrated 3Sp and Cruise, Thumb Throttle is not integrated, but still includes all the same functionality with appropriate parts
• Correctly Connected Cycle Analyst plug, with Shunt Value Marked on case for CA Shunt calibration
• Programming header for simple programming flash via USB program cable (program cable is an optional extra)
• E-brake with Motor kill and Regen (jumper enabled)
• Remote low power ignition switch connection (bar mounted power switch available). Zero current drain when low power switch is powered off, so not necesary to disconnect when not in use, avoiding the sparks and damage that the uncontrolled current surge can cause
Fully programmable using the optional USB program cable. The following functions/parameters can be modified:
• Battery and Phase current (inferred, not measured) can be independently adjusted
• Low Voltage Cut
• High Voltage Cut, or regen Voltage Limit
• 3 programmable speed settings
• Various Pedal Assist and Re-Gen braking paramters can be adjusted

Specification:

• 6pcs of Genuine IRFB3077 Mosfets. Just about the best 75V TO-220 Mosfet available
• 63V Caps, Max input voltage is limited to 60V
• 36-50V operation, 60V max
• 25A Current Limit
• 2.5mm² (Almost 13AWG) High Temperature Silicone wires used on Phase and Supply cables
• Dimension: 125 * 65 * 35mm
• Weight: 0.28kg

6 FET IRFB4110 INFINEON CONTROLLER (MOTOR WITH HALL SENSORS)
6 fet 4110, 36-72V Infineon Controller
Includes following functions as standard (we strongly recommend our matching Throttle are also purchased to make use of all functions and for plug and play simplicity:

• Throttle connection with Integrated push button cruise, separate 3 speed connection (Full and Half Twist include integrated 3Sp and Cruise, Thumb

Throttle is not integrated, but still includes all the same functionality with appropriate parts

• Correctly Connected Cycle Analyst plug, with Shunt Value Marked on case for CA Shunt calibration
• Programming header for simple programming flash via USB program cable (program cable is an optional extra)
• E-brake with Motor kill and Regen
• Jumper to select 36-60V or 72V operation

• Remote low power ignition switch connection (bar mounted power switch available). Zero current drain when low power switch is powered off, so not necesary to disconnect when not in use, avoiding the sparks and damage that the uncontrolled current surge can cause

Fully programmable using the optional USB program cable. The following functions/parameters can be modified:

• Battery and Phase current (inferred, not measured) can be independently adjusted
• Low Voltage Cut
• High Voltage Cut, or regen Voltage Limit
• 3 programmable speed settings
• Various Pedal Assist and Re-Gen braking paramters can be adjusted

Specification:

• 6pcs of Genuine IRFB4110 Mosfets. Just about the best 100V TO-220 Mosfet available
• 100V Caps, Max input voltage is limited to 90V
• 36-72V operation, 90V max (Jumper to select 60V plus)
• 25A Current Limit
• 2.5mm² (Almost 13AWG) High Temperature Silicone wires used on Phase and Supply cables
• Dimension: 125 * 65 * 35mm
• Weight: 0.28kg

9 FET IRFB3077 INFINEON CONTROLLER (MOTOR WITH HALL SENSORS)
9 fet 3077, 36-50V Infineon Controller
Includes following functions as standard (we strongly recommend our matching Throttle are also purchased to make use of all functions and for plug and play simplicity:
• Throttle connection with Integrated push button cruise, separate 3 speed connection (Full and Half Twist include integrated 3Sp and Cruise, Thumb Throttle is not integrated, but still includes all the same functionality with appropriate parts
• Correctly Connected Cycle Analyst plug, with Shunt Value Marked on case for CA Shunt calibration
• Programming header for simple programming flash via USB program cable (program cable is an optional extra)
• E-brake with Motor kill and Regen (jumper enabled)
• Remote low power ignition switch connection (bar mounted power switch available). Zero current drain when low power switch is powered off, so not necesary to disconnect when not in use, avoiding the sparks and damage that the uncontrolled current surge can cause
Fully programmable using the optional USB program cable. The following functions/parameters can be modified:
• Battery and Phase current (inferred, not measured) can be independently adjusted
• Low Voltage Cut
• High Voltage Cut, or regen Voltage Limit
• 3 programmable speed settings
• Various Pedal Assist and Re-Gen braking paramters can be adjusted

Specification:

• 9pcs of Genuine IRFB3077 Mosfets. Just about the best 75V TO-220 Mosfet available
• 63V Caps, Max input voltage is limited to 60V
• 36-50V operation, 60V max
• 30A Current Limit
• 2.5mm² (Almost 13AWG) High Temperature Silicone wires used on Phase and Supply cables
• Dimension: 155 * 85 * 45mm
• Weight: 0.45kg

9 FET IRFB4110 INFINEON CONTROLLER (MOTOR WITH HALL SENSORS)
9 fet 4110, 36-72V Infineon Controller
Includes following functions as standard (we strongly recommend our matching Throttle are also purchased to make use of all functions and for plug and play simplicity:
• Throttle connection with Integrated push button cruise, separate 3 speed connection (Full and Half Twist include integrated 3Sp and Cruise, Thumb Throttle is not integrated, but still includes all the same functionality with appropriate parts
• Correctly Connected Cycle Analyst plug, with Shunt Value Marked on case for CA Shunt calibration
• Programming header for simple programming flash via USB program cable (program cable is an optional extra)
• E-brake with Motor kill and Regen (jumper enabled)
• Remote low power ignition switch connection (bar mounted power switch available). Zero current drain when low power switch is powered off, so not necesary to disconnect when not in use, avoiding the sparks and damage that the uncontrolled current surge can cause
Fully programmable using the optional USB program cable. The following functions/parameters can be modified:
• Battery and Phase current (inferred, not measured) can be independently adjusted
• Low Voltage Cut
• High Voltage Cut, or regen Voltage Limit
• 3 programmable speed settings
• Various Pedal Assist and Re-Gen braking paramters can be adjusted

Specification:

• 9pcs of Genuine IRFB4110 Mosfets. Just about the best 75V TO-220 Mosfet available
• 100V Caps, Max input voltage is limited to 100V
• 36-72V operation, 90V max
• 30A Current Limit
• 2.5mm² (Almost 13AWG) High Temperature Silicone wires used on Phase and Supply cables
• Dimension: 155 * 85 * 45mm
• Weight: 0.45kg

12 FET IRFB3077 INFINEON CONTROLLER (MOTOR WITH HALL SENSORS)
12 fet 3077, 36-50V Infineon Controller
Includes following functions as standard (we strongly recommend our matching Throttle are also purchased to make use of all functions and for plug and play simplicity:
• Throttle connection with Integrated push button cruise, separate 3 speed connection (Full and Half Twist include integrated 3Sp and Cruise, Thumb Throttle is not integrated, but still includes all the same functionality with appropriate parts
• Correctly Connected Cycle Analyst plug, with Shunt Value Marked on case for CA Shunt calibration
• Programming header for simple programming flash via USB program cable (program cable is an optional extra)
• E-brake with Motor kill and Regen (jumper enabled)
• Remote low power ignition switch connection (bar mounted power switch available). Zero current drain when low power switch is powered off, so not necesary to disconnect when not in use, avoiding the sparks and damage that the uncontrolled current surge can cause
Fully programmable using the optional USB program cable. The following functions/parameters can be modified:
• Battery and Phase current (inferred, not measured) can be independently adjusted
• Low Voltage Cut
• High Voltage Cut, or regen Voltage Limit
• 3 programmable speed settings
• Various Pedal Assist and Re-Gen braking paramters can be adjusted

Specification:

• 12pcs of Genuine IRFB3077 Mosfets. Just about the best 75V TO-220 Mosfet available
• 63V Caps, Max input voltage is limited to 60V
• 36-50V operation, 60V max
• 40A Current Limit
• 4mm² (>11AWG) High Temperature Silicone wires used on Phase and Supply cables
• Dimension: 180 * 85 * 45mm
• Weight: 0.54kg

12 FET IRFB4110 INFINEON CONTROLLER (MOTOR WITH HALL SENSORS)
12 fet 4110, 36-72V Infineon Controller
Includes following functions as standard (we strongly recommend our matching Throttle are also purchased to make use of all functions and for plug and play simplicity:
• Throttle connection with Integrated push button cruise, separate 3 speed connection (Full and Half Twist include integrated 3Sp and Cruise, Thumb Throttle is not integrated, but still includes all the same functionality with appropriate parts
• Correctly Connected Cycle Analyst plug, with Shunt Value Marked on case for CA Shunt calibration
• Programming header for simple programming flash via USB program cable (program cable is an optional extra)
• E-brake with Motor kill and Regen (jumper enabled)
• Remote low power ignition switch connection (bar mounted power switch available). Zero current drain when low power switch is powered off, so not necesary to disconnect when not in use, avoiding the sparks and damage that the uncontrolled current surge can cause
Fully programmable using the optional USB program cable. The following functions/parameters can be modified:
• Battery and Phase current (inferred, not measured) can be independently adjusted
• Low Voltage Cut
• High Voltage Cut, or regen Voltage Limit
• 3 programmable speed settings
• Various Pedal Assist and Re-Gen braking paramters can be adjusted

Specification:

• 12pcs of Genuine IRFB4110 Mosfets. Just about the best 100V TO-220 Mosfet available
• 100V Caps, Max input voltage is limited to 90V
• 36-72V operation, 90V max
• 40A Current Limit
• 4mm² (>11AWG) High Temperature Silicone wires used on Phase and Supply cables
• Dimension: 180 * 85 * 45mm
• Weight: 0.54kg

18 FET IRFB4110 INFINEON CONTROLLER (MOTOR WITH HALL SENSORS)
18 fet 4110, 36-75V Infineon Controller
Includes following functions as standard (we strongly recommend our matching throttle are also purchased to make use of all functions and for plug and play simplicity):
• Throttle connection with Integrated push button cruise, separate 3 speed connection (Full and Half Twist include integrated 3Sp and Cruise, Thumb Throttle is not integrated, but still includes all the same functionality with appropriate parts
• Correctly Connected Cycle Analyst plug, with Shunt Value Marked on case for CA Shunt calibration
• Programming header for simple programming flash via USB program cable (program cable is an optional extra)
• E-brake with Motor kill and Regen (jumper enabled)
• Remote low power ignition switch connection (bar mounted power switch available). Zero current drain when low power switch is powered off, so not necesary to disconnect when not in use, avoiding the sparks and damage that the uncontrolled current surge can cause
Fully programmable using the optional USB program cable. The following functions/parameters can be modified:
• Battery and Phase current (inferred, not measured) can be independently adjusted
• Low Voltage Cut
• High Voltage Cut, or regen Voltage Limit
• 3 programmable speed settings
• Various Pedal Assist and Re-Gen braking paramters can be adjusted

Specification:

• 18pcs of Genuine IRFB4110 Mosfets. Just about the best 100V TO-220 Mosfet available
• 100V Rubycon Caps, Max input voltage is recommended 90V (charge voltage)
• Recommended 36-75V operation, 90V max
• 60A Current Limit
• 6mm2 (>10AWG) High Temperature Silicone wires used on Phase and Supply cables
• Dimension: 257 * 85 * 45mm
• Weight: 0.84kg