For Telecom cabinets and battery compartment cooling W-TEL Air Conditioners are designed for strict climate control in cabinets with temperature-sensitive electronic or telecommunications equipment. The closed loop cooling systems maintain a clean internal environment ensuring optimum performance and maximum service life of the enclosed electronics. Easy-to-install air conditioners W-TEL Air Conditioners are mono-block, plug and play units, which can be installed in- or outside the Telecom cabinet. Compared with a split air conditioner, the W-TEL Air Conditioner is easy to install, as no cooling engineer is required for installation. High reliability W-TEL products have been put into operation online in large quantities, and have undergone and passed strict field test, also win many domestic bids for outdoor cabinet solutions and is often appointed as the exclusive cooperative partner of relevant telecommunication stations. Intelligent control W-TEL Air conditioners with high reliability and flexible expandability, and data can be uploaded via protocols and dry contacts for remote supervision.Offering dry contacts and intelligent communication interfaces such as RS232, RS485, etc.W-TEL Air conditioners with IP55 degree could work outside for your projects . High energy-saving efficiency W-TEL Air conditioners with high energy-saving efficiency, and the integral energy efficiency is greatly improved by employing energy-saving compressors and advanced control logic. Silent demand The 53dB(A) silence air conditioners are tailored for outdoor cabinets neighboring residential communities, where low noise is a primary requirement. AC & DC Air conditioners DC powered air conditioner for outdoor battery cabinet, solar or wind powered outdoor cabinet. These series of air conditioner use DC powered compressor, so the whole system can also work in those areas that have no AC power or when the AC power is failed. AC POWER AIR CONDITIONER Model Capacity(W) AC Input Power(W) Installation Temperature IP degree (KG) (H*W*D)MM W-300 300 220V±10% 50/60HZ 150 Door mount -40 to +55 55 15 500*320*175 W-500 500 220V±10% 50/60HZ 390 Door mount -40 to +55 55 20 550*320*175 W-1000 1000 220V±10% 50/60HZ 400 Door mount -40 to +55 55 25 750*450*200 W-1500 1500 220V±10% 50/60HZ 525 Door mount -40 to +55 55 31 750*450*200 W-2000 2000 220V±10% 50/60HZ 600 Door mount -40 to +55 55 55 1100*410*320 W-3000 3000 220V±10% 50/60HZ 950 Door mount -40 to +55 55 70 1315*545*292 W-4000 4000 220V±10% 50/60HZ 1750 Door mount -40 to +55 55 90 1400*670*350 (Parameter may changed without notification) DC POWER AIR CONDITIONER Model Capacity(W) DC Input Power(W) Installation Temperature IP degree (KG) (H*W*D)MM W-500 500 48V 190 Door mount -40 to +55 55 20 492*445*195 W-1000 1000 48V 320 Door mount -40 to +55 55 35 1170*470*170 W-1500 1500 48V 500 Door mount -40 to +55 55 40 1170*470*170 W-2000 2000 48V 830 Door mount -40 to +55 55 55 1200*500*200 W-3000 3000 48V 1000 Door mount -40 to +55 55 70 1315*545*292 (Parameter may changed without notification) Projects sites

Summary: W-TEL-1xN PLC splitter device 1 x N PLC Splitter The light source distribution is accomplished on the chip inside. It can make more than 1*32 on one chip. Applications: Telecommunication systems; Digital, hybrid and AM-Video system; CATV systems ; four different mould 1*4/8/16/32, according with Telcordia GR-1209 &GR-1221, low insertion loss, high reliability, sophisticated design of high homogeneity. Specifications: Can meet the requirement of different transmit wavelength Optical parameter to meet the need of different customers :P level and S level Good light source distribution, can divide light signal to user equally. Compact size, take 1*32 PLC splitter as an example 4mm*7mm*50mm, can be installed directly in different in optical fiber cross connect cabinet, no need of special design to leave large space. One set can load more than 1*32 splitter Low cost advantage Technical Index: Performance Index Fused fiber splitter PLC Splitter Operating wavelength (nm) 1310(1550) ± 40nm 1260~1650nm Distribution Rate Changeable uniform Insertion Loss ( dB) Max. 1×4 7.2 1×8 10.5 1×4 7.2 1×8 10.5 1×16 14.0 1×32 17.5 1×16 13.5 1×32 16.5 Insertion Loss Uniformity (dB) 1×4 1.6 1×8 1.8 1×4 0.6 1×8 0.8 Max. 1×16 2.4 1×32 3.0 1×16 1.2 1×32 1.7 PDL(dB) 0.3 0.1

Application: fiber optic communication network fiber broadband access network CATV    fiber instruments fiber LAN Material: 1 Sleeve ceramic sleeve or Japan phosphor bronze 2 Attenuation fiber cable from Japan 3 Exterior components Japan, China or USA 4 core: ceramic (Japan or China) 5 exterior components: Japan or USA or China (optional) 6 fiber Corning FC/PC patch cord Duplex Multimode patch cord SC/APC patch cord Waterproof 2 cores pigtail Waterproof 4 cores pigtail Waterproof 8 cores pigtail Optical bundle connector Soft fiber cable connector Optical ribbon connector Features: 1 Low insertion loss and back reelection loss 2 Ferrule end surface predated 3 Precision anti-rotation key and corrosion resistant body 4 UL-rated plastic housing 5 Telcordia style boots 6 Boots in a variety of colors 7 Free-looting ceramic ferrule Technical dependability data (test): Test item Test condition Wet- Temperature:85 /relative humidity resistance 85 /14Days/insertion loss≤0.1Db Temperature Temperature-40 ~+75 /relative Humidity 10 -80 /42 repetitions/ change 14days/ insertion loss≤0.1Db Put in water Temperature43 , /ph5.5,/ 7Days / insertion loss≤0.1Db Swing1.52Mm/frequency 10hz 55hz, Vibrancy X y z three Directions:2 hours Insertion loss≤0.1Db Load bend 0.454Kgload/circle 100 Insertion loss≤0.1Db Load torsion 0.454Kgload/10 circles Insertion loss ≤0.1Db Senility 0.23Kg pull nakedness fiber -resistance 1.0Kg(with shell ) insertion≤0.1Db Strike High 1.8M,three directions ,8 in each direction/insertion loss≤0.1Db Reference Bell core ta-nwt-001209 standard Insertion loss≤0.1Db SPECIFICATIONS: Type Insertion Loss Insertion Loss Insertion Loss Return Loss Return Loss Return Loss international enterprise typical international enterprise typical PC ≤0.5dB ≤0.20dB ≤0.10dB 40 dB 45 dB 45 dB UPC ≤0.5dB ≤0.20dB ≤0.10dB 40 dB 45 dB 45 dB APC ≤0.5dB ≤0.20dB ≤0.10dB 40 dB 45 dB 45 dB

Usage: Suitable for installing and placing the 19” standard equipment and the equipment of metric and ETIS standards. OEM design from 2U 4U 6U 8U 12U 15U 18U 22U 24U 26U 28U 32U 36U 42U 48U 52U in capacity. Main features: Complete types and specifications. Customized cabinets are also available upon request. Modular design for all parts to meet your any configuration needs. Wiring holes reserved on both the upper and the lower covers for free cabling. Sufficient cabling space inside the cabinet with routes designed on all sides. L Side panel detachable and special components for cabinet combining. Safe and reliable grounding protection. The bottom, top, air blow, air ejection and heat ejection can be chosen to raise the reliability of the equipment; Firm structure with the maximum static load of 1200kg ； Pedestals, sole angles and bottom wheels can be chosen to secure the machine cabinet; Front and back doors, light and right doors, copings and sole plate are convenient for disassembly and assembly; Degrease, acid wash, antisepticised with phosphor, water washing ,imported plastic powder coating with plastic static spraying. Design characteristics: ·The appearance design is luxurious and handsome, fully in accordance with the 19" Standard and ETSI Standard followed by international inter-net products; ·It wholly uses high-quality SPCC cold rolling steel plate with the thickness of 1.2-2.0mm and the maximum static load of 800kg; ·The whole case is welded strongly. The strong shell of the case can ensure the safe operation of the system in any environment; ·The visual area of the front door is large so that it is convenient for observing equipment; ·The meshes of high density of the front door sealing strip are fit for ventilation and heat emission of the equipment; ·Beautiful and decent after static electricity plastic spraying,colors can be chosen by the customers.; ·The whole machine is dealt with through phosphate antisepsis plastic spraying. Floor standing type W-TEL-NWC- wall mounted small type cabinet has many advantages such as small size ,compact ,space saving etc. mainly used to contain network equipment and small servers etc. And we can design according to customer’s requests. It is widely used in computer data network, controlling and so on. Wall mount type Projects for Michigan network data center

SM/MM Fiber Optic Adapter As a kind of commonly seen fiber optic assembly, the fiber optic adapter or fiber optic coupler is available in single mode and multimode versions. It is mainly used for connection and fixing of optical fiber connectors. The two connectors are precisely aligned and locked up by the alignment structure of the optical fiber adapter, thus ensuring low insertion loss. The fiber optic adapter has two different internal structures for alignment. One is to utilize precise ceramic or copper sleeve to complete alignment. Most of fiber optic cable adapters, including SC, LC, FC, ST, D4, and DIN types, make use of the structure. The other one is to achieve accurate alignment by using PIN and PIN hole. This structure is mainly used in MT series fiber optic adapters such as MT-RJ, MPO and MPO type. According to the types of the two connectors combined, the fiber optic adapter can be divided into three categories: the non transfer-type like SC-SC and LC-LC; the transfer-type including SC-LC and SC-FC; and the female-male fiber adapters such as SC (female)-FC (male). Fiber optic adapters can be often seen in FTTx, MANs, WANs, CATV, etc. In the computer rooms of buildings or residential areas, thousands of patch cords are connected and communicate with each other. Fiber adapter is indispensable in connection of patch cords. It is also used to connect devices together and for the production tests of other passive devices. The complete set of optic passive components production and assembly facility and measurement instrument imported from USA and Japan for the establishment of the optic passive production line, available in traditional FC, SC and ST optic cable connectors and LC, duplex SC, MF-RJ and MU small size optic fiber connectors. All movable optical fiber connectors have passed inspection by the Quality Supervision & Inspection Center of Optical Communication Products (QSICO) under the Ministry of Information Industry (MII). Item Parameter Material FBT Color Gray Scope PC&APC Insertion Loss ≦0.2dB Operation Time 500 times without distortion and crack, Variety Insertion Loss≦0.1dB Insertion Loss -40 ~ +85℃ Mechanical Durability 50N, connection with two connectors, connection time of 30min Temperature 40N, connection with two connectors, connection time of 30min Axial Tension Force >8 N Side Shear Force -40～+75℃

W-TEL-PDC Electric Power Distribution cabinet is used to distribution electric power both indoor and outdoor of telecommunication cabinet. The surface material is spray coating plastics, which is anti-rust and antisepsis. High –quality of air switch is used inside the cabinet, which can ensure good air and heat exchanging. This can be mounted directly on walls. Product Features: The OEM design cabinet is made of cold rolled steel and the surface material is spray coating plastics, contour Artistic. Integration electric power distribution panel optional types: thunder resistance or no thunder resistance.

Summary: W-TEL-OTC series outdoor telecommunication cabinet is mainly used in the field of traffic, CATV, electric power etc.Can be used under different conditions: gale, rain, snow, hail, frost, smog and solar radiate etc.The main part of the cabinet is made of magnesium and aluminum alloy. It can be last for 30 years of normal use. Specification: Cabinet materials: high-quality aluminum alloy and zinc sheet Adapts to frame design of "Sandwich" panel Temperature management, control system, power supply system, entrance guard, environment supervisory system and wiring unit module Cabinet meets the requirements of IP65 level of protection Double layer (with heat insulation layer inside) Weather resistant & anti-graffiti painting. RAL7035 power coated EMC protection Corrosion protection. Vandal proof design with 3 pointing locking system. Adopt special imported outdoor industrial air- Conditioner/heat-exchanger/TEC/Fan system for cooling control The perfect earthing system to protect it from thunder. The enshroud dustproof net is installed in the air circulation system to protect the entry of dust and insects. Special A4 size material box and unique PC panel, easy maintenance and operating. Operation of W-TEL outdoor telecom cabinet : Temperature :-45°to +55° Humidity : ≤90(30°) Atmospheric pressure :70-106Pa Protection : IP65 Type 1 < Air-con model > Air-con cabinet adopts the frames design of "Sandwich", The inner and outer cabinet are all made of high quality aluminum alloy ,zinc sheet covered with aluminum and zinc sheet covered with magnesium with good capability of preservation , which use 3-4 point security locking system from anti-theft safely .The thermal insulation materials en-chased in the component can prevent conductive heat like outdoor ultraviolet radiation from infiltrating into the cabinet , select professional air -con with the modulation of constant temperature and humidity and setting of heating to ensure the cabinet provided with the best operating environment . The inside is composed of standard 19inch rack frame , temperature management and control system , power supply system , entrance guard , environment supervisory system and wiring unit module etc .The cabinet meets the requirement of IP65 level of protection . Type 2 < Heat-exchanger model > Cabinet of heat-ex-changer model adopts the frame design of " Sandwich " panel . and the inner and outer cabinet are all made of high - quality alloy or stainless steel panel with good capacity of preservation . which introduce the 3 point latch-up structure to strengthen the safety of the cabinet . The thermal insulating insulating material en-chased in the component can prevent the conductive heat like outdoor ultraviolet radiation from infiltrating in the cabinet , select heat-ex-changer system with heater to ensure the environment inside of the cabinet meet the requirements of the normal movement of communications equipment , The inside is composed of standard 19-inch frame , temperature management and control system , power supply , door guard , environment monitoring system and wiring system etc .  The cabinet meets IP 65 protection level . Type 3 < Fan model > Fan model cabinet adopts to sandwich panel and both of the inner and outer are made of high quality aluminum alloy and stainless steel sheet with good capacity of preservation , which introduce the security 3 point locking system for anti-theft . Special thermal material can prevent the outdoor ultraviolet radiation from infiltrating into the cabinet effectively . select the glands trip of special material to ensure the long-term sealing performance of the cabinet , the fan and air out take equipment on the top guarantee timely and high efficient heat emission . Cabinet meets IP65 level . Cabinet protection : Projects :

Outdoor project connects the feeder optical cable led out from the premise to the distribution optical cable led in the user’s building. The outdoor project involves such products as Fiber Distribution Cabinets, and Fiber Splice Closures. Fiber Distribution Cabinets can be selected depending on different ODN structures. It completes inlet and fixing of optical cables, splicing and termination of fibers and installation and management of optical splitter on an xPON access network and implements optical line splitting and capacity expansion. It can be used to install the optical splitter with different numbers of optical splitting ports. Fiber Splice Closures provide splice function between feeder cables and distribution cables. On the FTTx network, the fiber splice closures can also take over some functions of Fiber Distribution Cabinets. Fiber distribution cabinet Used for rapid network deployment this cabinet offers connection, distribution and dispatching of communication optical cables from the central office to each optical distribution node. It provides secure and reliable management of flexible fiber and optical cables. Features 1. High-quality steel sheet, surface plastic spray 2. Effective sealing performance, dust and splash proof: IP65 3. Single door, front operation 4. Modular structure, easy configuration 5. Rotary structure of optical patch panel 6. Available in FC, SC, ST, duplex LC adapters 7. Storage of the pigtails or fiber patch cords at the front 8. Perfect fiber route design to ensure bend radius of fibers 9. Reliable optical cable fixing, stripping protection and grounding Wall mount distribution box A indoor distribution system mainly adopted as a base station with base band unit (BBU) and radio remote unit (RRU). With the introduction of multiband RRU, indoor distribution systems need a large number of fiber resources. Sufficient fiber resources should be distributed and routed at one time in during the installation process. To meet the demands of various equipment interface from potential manufactures, pre-distributed multi-fibers should be terminated using the tower-mounted distribution box. It implements such functions as the inlet, fixation, and stripping protection for subscriber cables, splicing, protection, storage and management for optical fibers. It is used for connection from fiber to tower or from fiber to building, for connecting RRU and BBU. It is installed in the building or OSP near the antenna. Features 1. Pleasant appearance, easy installation single-mode double-fiber outside patch cord 2. Using bottom cable inlet locations, no interference among cables 3. Well designed structure and layout, convenient for routing and maintenance 4. Sealed enclosures protect fibers from rain and dust 5. Full front operation, single door 6. Termination using duplex LC adapter, mating with adapter at RRU end 7. Selective lower sealing assembly, compatible with outdoor connector and outdoor LC-type dual jumper fiber 8. Supporting wall-mounted or pole-mounted, adjustable range for pole-mounted is 60mm-120mm Fiber Splice Closure The optical fiber distribution box is applicable to connection and distribution management of optical cables. On the FTTx network, the fiber splice closure can also take over some functions of the optical cross connection cabinet and optical distribution box, and higher requirements are put forward for the number of inlet cables of the fiber splice closure. FTTC Outdoor Cabinet Feature 1. For FTTC application and can accommodate DSLAM, AG equipment 2. Single or several cabinets structure 3. Suit for base-mounted or overhead mounted FTTB Outdoor Cabinet Features 1. Provide broadband and voice service 2. Modular design with single or multi compartments to accommodate ONU equipment, batteries and voice & broadband blocks 3. Wall mounting or floor installation with plinth

Feature: Both IDC and wire wrap connection modules are available. The connection block is consisting of double side colorful terminals which make easy operation and maintenance. Operator could finish connection only by a screw drive. The body and pedestal are made of stainless steel or high quality cold rolling steel or Sheet Molding Compound (SMC).The life span is over 20 years for stainless steel body and SMC body, over 10 years for cold rolling steel body. The hinges are placed on both sides, providing enough space for operation when the doors are fully opened. Anti-drew design. Heat insulation material is incorporated into the cabinet to provide effective protection against dew. Operator could ease test the cabinet by outside testing pin. Technical feature: Insulation resistance: 50000M /500V(DC) Withstanding Voltage: 500V(50HzAC) 1 min without spark or arc. Terminal contact resistance:≤3M Contact resistance between reeds:≤20M Pulling force: 0.4mm>50N, 1.2mm>50N Connection durability: more than 1000 times

Digital Distribution Frame The modular device uses 75W coaxial connectors, which facilitate installation, operation and capacity expansion. The frame, made of aluminum profiles and connecting parts, is characterized by an open building block structure and concise design with cable-through rings equipped for easy cabling and jumping. The frame and supports rack are made of anodized aluminum profiles while the shielding cover of the coaxial connectors is specially treated with epoxy electrostatic spraying to boast beautiful appearance and powerful anti-corrosion capability. The terminal box of the coaxial connectors boasts excellent shielding capability and interchangeability to ensure the stability and reliability of major technical indices. High-end and low-end Distribution Units are welded through jumpers and can rotate by 1800 to facilitate cable welding. Open type Sealing type The frame is made from quality materials such as aluminum alloy, steel plate etc. The surface is treated by way of galvanization, oxidization, plastics coating etc. The structure is stable with pleasing appearance. Module structure is adopted for flexible and easy installation and deployment. Rotary structure is designed for each unit. The unit can be rotated downward freely for convenient cable connection and maintenance Enough wire hooking rings and support trays are provided for the frame for easy cable laying. The frame is equipped with perfect earth system The shield cover of coaxial connector is treated with epoxy static plastics spray with pleasing appearance and good performance of anti-erosion. The contact reed of module is treated with gold plating so as to ensure contact reliability and safety. Unit connection

Feature: Corrosion-proof alloy aluminum or SMC or ABS base and cover. The cover and base feature superior anti-rust performance, suitable for harsh outdoor condition. The cabinet is either pole mounted or wall mounted.IDC and wire wrap modules are available. Suitable for the connection between branch line and the communication line in the city, county and countryside. The type of wall inlaid indoor branch box was suitable for the connection between indoor communication cables and the user lines. (1)Outdoor type：The body of the case is made of aluminum alloy castings, with spray-painted face, elegant and anti-corrosion; the reasonable structure of right-opened case-cover and reversible block leading to better airproof and easy opening or operation. There is pressive button for fixing cable indoor, in order to prevent from dropping of cable lug when forcing; it is better airproof for using rubber sealing loop between the body and the cover; reversible block leading to easy opening or operation; the fixing method as special design can save installation time and to lighten labor intensity of pole in field; add the space of the case properly, that can insure the good sealing of bottom case cover when fully loaded. (2)Indoor type: attractive appearance, borderline smooth, reversible block leading to easy opening or operation. Technical Indexes ·Suitable for the connection between branch line and the communication line in the city, county and countryside. ·The body of the case is made of aluminum alloy castings, smooth and stable. ·The reasonable structure of right-opened case-cover and reversible block leading to better airproof and easy opening or operation. ·pressive button for fixing cable indoor, in order to prevent from dropping of cable lug when forcing. ·the fixing method as special design can save installation time and to lighten labor intensity  of pole in field ·add the space of the case properly, that can insure the good sealing of bottom case cover when fully loaded. Main Technical Indexes: ·Environmental temperature ：－25℃～+40℃ ·Relative humidity：<95% ·Contact resistance between the lead and the end：≤5×10-3Ω ·Voltage-resistance strength：non-puncture, no arc-over 500VAC/1min Instruction Manual Environment Condition: Environment temperature: －55℃～+55℃    Environment temperature: －25℃～+55℃ Relative humidity: ≤95%                   Relative humidity: ≤95% Atmospheric pressure:70～160kp            Atmospheric pressure:70～160kp Electrical Performance Contact resistance: <5×10-3Ω Voltage-resistance:﹥ 5×103MΩ Voltage resistance strength：non-puncture, no are-over under 500Vac/30s Installation Method pole-hanged installation Fixing the hoop on the electrical pole with M12 bolt, and then let the branch cable clip. Wall-mounted installation Outdoor distribution box Ambient Temperature:-55x+55 Relative Humidity:≤95%(+30 ) Pressure: 70kPax106kPa. Indoor distribution box Ambient Temperature:-25x+40 Relative Humidity:≤95%(+30) Pressure:70kPax106kPa

Summary: Wide Band Access cabinet is designed for living blocks, can install Ethernet exchanger, optical splice tray, light and power transmitter, power module, CAT5 wiring connection module and audio module. Specification: Can install optical fiber transmitter and optical pigtails, connect earth net Can install ADSL equipment and wiring connection fix device, used to Connect ADSL has the wiring fix device for network equipment, wire holder and Transmitter has protecting plug of audio cable distribution and electric power connection thunder resistance anti-theft device Technical specification: Power: multi-plug Fan start temperature: thunder resistance Working conditions: -10-55 working temperature: -10-55 Humidity 5 90 Non-condensing